Step Plumbing Guide for Bathtub Installation
Step Plumbing Guide for Bathtub Installation
Blog Article
What're your concepts about How to Install a Bathtub Yourself?
Mounting a tub isn't precisely rocket science, but it does require strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bathtub with a new one is likewise a moderately hard project. If the old bathtub is readily accessible, the task can move rapidly; if you have to open up a wall to eliminate the old tub as well as position the brand-new bath tub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will certainly need an assistant to vacate the old tub as well as embeded in the new one. Ensure you have actually certified yourself for the job as well as fit trying it. Rather than hiring a service provider to take control of a halfway-completed project, it is better to think about utilizing one before you begin. Possibilities are you may need a professional plumber to make tube connections.
This article will certainly aid you install a new tub in your bathroom if you have actually already purchased a new bathtub and don't need to change the setup of your previous water pipelines.
Your tools and also material checklist need to make up the following:
Getting ready for the Installment
First of all, the sustaining frame supplied with the bathroom needs to be fitted (if required) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is necessary to make sure that if the tap includes a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to avoid strain on the bath tub.
Fit the adaptable faucet connectors to the bottom of both faucets using 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. See to it you use all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final position.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you must do is detach the water supply. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing taps can be quite troublesome because of the restricted access that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a fabric ready for the staying water that will come from the pipelines. Once the supply pipelines have actually been removed, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
Before carrying on to fit the brand-new faucets, compare the pipe links on the old taps to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the new taps to fit.
Setting up the Bath tub
Making use of the two wooden boards under its feet, put the tub in the called for placement. The wood boards are valuable in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level and also readjusting the feet on the bath tub until the spirit level reads degree.
To set up faucets, fit the bottom of the outermost versatile tap connector to the proper supply pipe by making a compression sign up with; then do the same for the other faucet.
Turn on the water supply and inspect all joints and also new pipework for leaks as well as tighten them if necessary. Load the tub as well as likewise check the overflow outlet as well as the normal electrical outlet for leaks.
Ultimately, take care of the bathroom paneling as described in the manufacturer's instruction manual. Tiling and securing around the tub ought to wait until the tub has actually been utilized a minimum of once as this will settle it into its last placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the installing opening in the bath/basin guaranteeing that the washers remain in place in between the faucet and the sink. Safeguard the tap in place with the supplier supplied backnut. Once the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet ports. The previous kind needs to be attached to the faucet finishes first, tightening up only by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to split a rigid seal, triggering the water to pass through the wall between the bathroom and also the tiling, resulting in problems with wetness as well as feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your fixtures and also fittings. They are offered in tubes and also cartridges, and are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of drenched newspaper or soft rope. Remember to always load the bath tub with water prior to sealing, to allow for the activity experienced when the tub is in usage. The sealant can break fairly very early if you do not take into consideration this motion prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily readily available on the market. It is suggested to fit the tiles using waterproof or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic reader about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I figured sharing that topic was appropriate. Sharing is good. Helping people is fun. I praise you for your time. Visit us again soon.
Contact Us Report this page